title image


Smiley Re: wlan mit suse 9.3 - newbie
Hi bazehnk,



habe ich alles ganz brav gemacht. Hier der output.

Was nun?????





/sbin/ifconfig

eth0 Link encap:Ethernet HWaddr 00:A0:CC:DF:53:F8

inet addr:192.168.1.34 Bcast:192.168.1.255 Mask:255.255.255.0

inet6 addr: fe80::2a0:ccff:fedf:53f8/64 Scope:Link

UP BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1

RX packets:79201 errors:0 dropped:0 overruns:0 frame:0

TX packets:44274 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:108191834 (103.1 Mb) TX bytes:3370027 (3.2 Mb)

Interrupt:10 Base address:0xcc00



lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0

inet6 addr: ::1/128 Scope:Host

UP LOOPBACK RUNNING MTU:16436 Metric:1

RX packets:279 errors:0 dropped:0 overruns:0 frame:0

TX packets:279 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:18558 (18.1 Kb) TX bytes:18558 (18.1 Kb)





ping 192.168.1.1

PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.

From 192.168.1.34: icmp_seq=2 Destination Host Unreachable

From 192.168.1.34 icmp_seq=2 Destination Host Unreachable

From 192.168.1.34 icmp_seq=3 Destination Host Unreachable

From 192.168.1.34 icmp_seq=4 Destination Host Unreachable

From 192.168.1.34 icmp_seq=6 Destination Host Unreachable

From 192.168.1.34 icmp_seq=7 Destination Host Unreachable

From 192.168.1.34 icmp_seq=8 Destination Host Unreachable









Linux version 2.6.11.4-21.2-default (geeko@buildhost) (gcc version 3.3.5 20050117 (prerelease) (SUSE Linux)) #1 Thu Apr 21 09:37:56 UTC 2005

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)

BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)

BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)

BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)

BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)

BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)

BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)

BIOS-e820: 00000000ffee0000 - 00000000fff0ffff (reserved)

BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)

0MB HIGHMEM available.

511MB LOWMEM available.

On node 0 totalpages: 131056

DMA zone: 4096 pages, LIFO batch:1

Normal zone: 126960 pages, LIFO batch:16

HighMem zone: 0 pages, LIFO batch:1

DMI 2.3 present.

ACPI: RSDP (v000 AMI ) @ 0x000fa240

ACPI: RSDT (v001 AMIINT SiS645XX 0x00000010 MSFT 0x0100000b) @ 0x1fff0000

ACPI: FADT (v001 AMIINT SiS645XX 0x00000011 MSFT 0x0100000b) @ 0x1fff0030

ACPI: DSDT (v001 SiS 645 0x00001000 MSFT 0x0100000d) @ 0x00000000

ACPI: PM-Timer IO Port: 0x808

ACPI: local apic disabled

Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000)

Built 1 zonelists

Kernel command line: root=/dev/hda3 vga=0x317 selinux=0 splash=silent resume=/dev/hda2

bootsplash: silent mode.

Initializing CPU#0

PID hash table entries: 2048 (order: 11, 32768 bytes)

Detected 1992.666 MHz processor.

Using pmtmr for high-res timesource

Console: colour dummy device 80x25

Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

Memory: 514228k/524224k available (1866k kernel code, 9372k reserved, 658k data, 204k init, 0k highmem)

Checking if this processor honours the WP bit even in supervisor mode... Ok.

Calibrating delay loop... 3948.54 BogoMIPS (lpj=1974272)

Security Framework v1.0.0 initialized

SELinux: Disabled at boot.

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00000000 00000000 00000000

CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000 00000000 00000000 00000000

CPU: Trace cache: 12K uops, L1 D cache: 8K

CPU: L2 cache: 512K

CPU: After all inits, caps: bfebf9ff 00000000 00000000 00000080 00000000 00000000 00000000

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

CPU0: Intel P4/Xeon Extended MCE MSRs (12) available

CPU0: Thermal monitoring enabled

CPU: Intel Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz stepping 07

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... OK.

checking if image is initramfs... it is

Freeing initrd memory: 1335k freed

ACPI: Looking for DSDT in initrd... not found!

not found!

ACPI: setting ELCR to 0200 (from 0c20)

NET: Registered protocol family 16

PCI: PCI BIOS revision 2.10 entry at 0xfda41, last bus=1

PCI: Using configuration type 1

mtrr: v2.0 (20020519)

ACPI: Subsystem revision 20050211

ACPI: Interpreter enabled

ACPI: Using PIC for interrupt routing

ACPI: PCI Root Bridge [PCI0] (00:00)

PCI: Probing PCI hardware (bus 00)

Uncovering SIS962 that hid as a SIS503 (compatible=1)

Enabling SiS 96x SMBus.

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

ACPI: Power Resource [FDDP] (off)

ACPI: Power Resource [LPTP] (off)

ACPI: Power Resource [URP2] (off)

ACPI: Embedded Controller [EC0] (gpe 11)

ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)

ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)

ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)

ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)

ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *10 11 12 14 15)

ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *10 11 12 14 15)

ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 7 10 11 12 14 15)

ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 *11 12 14 15)

Linux Plug and Play Support v0.97 (c) Adam Belay

pnp: PnP ACPI init

pnp: PnP ACPI: found 10 devices

PCI: Using ACPI for IRQ routing

PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report

TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)

apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)

apm: overridden by ACPI.

audit: initializing netlink socket (disabled)

audit(1120322158.832:0): initialized

Total HugeTLB memory allocated, 0

VFS: Disk quotas dquot_6.5.1

Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

Initializing Cryptographic API

vesafb: framebuffer at 0xc8000000, mapped to 0xe0880000, using 6144k, total 65536k

vesafb: mode is 1024x768x16, linelength=2048, pages=41

vesafb: protected mode interface info at c000:56f5

vesafb: scrolling: redraw

vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0

bootsplash 3.1.6-2004/03/31: looking for picture... silentjpeg size 57135 bytes,...found (1024x768, 36789 bytes, v3).

Console: switching to colour frame buffer device 127x44

fb0: VESA VGA frame buffer device

isapnp: Scanning for PnP cards...

isapnp: No Plug & Play device found

Real Time Clock Driver v1.12

PNP: PS/2 Controller [PNP030b:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12

i8042.c: Detected active multiplexing controller, rev 1.0.

serio: i8042 AUX0 port at 0x60,0x64 irq 12

serio: i8042 AUX1 port at 0x60,0x64 irq 12

serio: i8042 AUX2 port at 0x60,0x64 irq 12

serio: i8042 AUX3 port at 0x60,0x64 irq 12

serio: i8042 KBD port at 0x60,0x64 irq 1

Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled

ttyS0 at I/O 0x3f8 (irq = 4) is a 8250

ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10

PCI: setting IRQ 10 as level-triggered

ACPI: PCI interrupt 0000:00:02.6[C] -> GSI 10 (level, low) -> IRQ 10

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

FDC 0 is a National Semiconductor PC87306

RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize

loop: loaded (max 8 devices)

mice: PS/2 mouse device common for all mice

input: PC Speaker

md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27

NET: Registered protocol family 2

IP: routing cache hash table of 4096 buckets, 32Kbytes

TCP established hash table entries: 32768 (order: 6, 262144 bytes)

TCP bind hash table entries: 32768 (order: 5, 131072 bytes)

TCP: Hash tables configured (established 32768 bind 32768)

NET: Registered protocol family 1

PM: Checking swsusp image.

PM: Resume from disk failed.

ACPI wakeup devices:

PCI0 PS2M PS2K EC0 LID USB1 USB2 USB3 USB4 S139 LAN MDM AUD SLPB

ACPI: (supports S0 S3 S4 S5)

Freeing unused kernel memory: 204k freed

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

SIS5513: IDE controller at PCI slot 0000:00:02.5

SIS5513: chipset revision 0

SIS5513: not 100% native mode: will probe irqs later

SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller

ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA

ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA

Probing IDE interface ide0...

input: AT Translated Set 2 keyboard on isa0060/serio0

hda: TOSHIBA MK4018GAS, ATA DISK drive

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

Probing IDE interface ide1...

hdc: TOSHIBA DVD-ROM SD-R6012, ATAPI CD/DVD-ROM drive

ide1 at 0x170-0x177,0x376 on irq 15

hda: max request size: 128KiB

Synaptics Touchpad, model: 1

Firmware: 4.1

Sensor: 8

new absolute packet format

input: SynPS/2 Synaptics TouchPad on isa0060/serio2

hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(33)

hda: cache flushes supported

hda: hda1 hda2 hda3

hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)

Uniform CD-ROM driver Revision: 3.20

Attempting manual resume

PM: Checking swsusp image.

swsusp: Suspend partition has wrong signature?

PM: Resume from disk failed.

ReiserFS: hda3: found reiserfs format "3.6" with standard journal

ReiserFS: hda3: using ordered data mode

reiserfs: using flush barriers

ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30

ReiserFS: hda3: checking transaction log (hda3)

ReiserFS: hda3: Using r5 hash to sort names

bootsplash: status on console 0 changed to on

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

Adding 1020116k swap on /dev/hda2. Priority:42 extents:1

device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com

cdrom: open failed.

NTFS driver 2.1.22 [Flags: R/W MODULE].

NTFS volume version 3.1.

NTFS-fs warning (device hda1): load_system_files(): Volume is dirty. Will not be able to remount read-write. Run chkdsk and mount in Windows.

Capability LSM initialized

ieee1394: Initialized config rom entry `ip1394'

ieee1394: raw1394: /dev/raw1394 device initialized

ohci1394: $Rev: 1250 $ Ben Collins

ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5

PCI: setting IRQ 5 as level-triggered

ACPI: PCI interrupt 0000:00:02.3[B] -> GSI 5 (level, low) -> IRQ 5

ohci1394: fw-host0: Unexpected PCI resource length of 1000!

ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[5] MMIO=[dbfff000-dbfff7ff] Max Packet=[2048]

video1394: Installed video1394 module

parport: PnPBIOS parport detected.

parport0: PC-style at 0x378, irq 7 [PCSPP]

lp0: using parport0 (interrupt-driven).

ieee1394: Host added: ID:BUS[0-00:1023] GUID[00030d532510da4e]

usbcore: registered new driver usbfs

usbcore: registered new driver hub

load_module: err 0xffffffef (dont worry)

ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)

ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10

ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 10 (level, low) -> IRQ 10

ohci_hcd 0000:00:03.0: OHCI Host Controller

ohci_hcd 0000:00:03.0: irq 10, pci mem 0xdbffb000

ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10

ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 10 (level, low) -> IRQ 10

ohci_hcd 0000:00:03.1: OHCI Host Controller

ohci_hcd 0000:00:03.1: irq 10, pci mem 0xdbffc000

ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 5

ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 5 (level, low) -> IRQ 5

ohci_hcd 0000:00:03.2: OHCI Host Controller

ohci_hcd 0000:00:03.2: irq 5, pci mem 0xdbffd000

ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3

hub 3-0:1.0: USB hub found

hub 3-0:1.0: 2 ports detected

load_module: err 0xffffffef (dont worry)

load_module: err 0xffffffef (dont worry)

ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11

PCI: setting IRQ 11 as level-triggered

ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 11 (level, low) -> IRQ 11

ehci_hcd 0000:00:03.3: EHCI Host Controller

ehci_hcd 0000:00:03.3: irq 11, pci mem 0xdbffe000

ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4

PCI: cache line size of 128 is not supported by device 0000:00:03.3

ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 4-0:1.0: USB hub found

hub 4-0:1.0: 6 ports detected

NET: Registered protocol family 10

Disabled Privacy Extensions on device c033d600(lo)

IPv6 over IPv4 tunneling driver

ip6_tables: (C) 2000-2002 Netfilter core team

Linux agpgart interface v0.100 (c) Dave Jones

agpgart: Detected SiS 646 chipset

agpgart: Maximum main memory to use for agp memory: 439M

agpgart: AGP aperture is 64M @ 0xdc000000

sis900.c: v1.08.07 11/02/2003

ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10

ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 10 (level, low) -> IRQ 10

0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.

0000:00:04.0: Using transceiver found at address 1 as default

eth0: SiS 900 PCI Fast Ethernet at 0xcc00, IRQ 10, 00:a0:cc:df:53:f8.

ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 10 (level, low) -> IRQ 10

ohci_hcd 0000:00:03.1: wakeup

i2c-sis96x version 1.0.0

Linux Kernel Card Services

options: [pci] [cardbus] [pm]

usb 2-2: new low speed USB device using ohci_hcd and address 2

ip_tables: (C) 2000-2002 Netfilter core team

intel8x0_measure_ac97_clock: measured 49353 usecs

intel8x0: clocking to 48000

sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00

ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11

ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 11 (level, low) -> IRQ 11

Yenta: CardBus bridge found at 0000:00:08.0 [1584:3000]

Yenta O2: res at 0x94/0xD4: 00/ea

Yenta O2: enabling read prefetch/write burst

Yenta: ISA IRQ mask 0x0018, PCI irq 11

Socket status: 30000821

ip_conntrack version 2.1 (4095 buckets, 32760 max) - 248 bytes per conntrack

bootsplash: status on console 0 changed to on

BIOS EDD facility v0.16 2004-Jun-25, 1 devices found

cs: IO port probe 0xc00-0xcff: clean.

cs: IO port probe 0x820-0x8ff: excluding 0x828-0x877 0x898-0x89f

cs: IO port probe 0x800-0x80f: clean.

cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f 0x4d0-0x4d7

cs: IO port probe 0x100-0x3af: excluding 0x1c0-0x1cf

cs: IO port probe 0xa00-0xaff: clean.

Disabled Privacy Extensions on device dda6f400(sit0)

cdrom: open failed.

SCSI subsystem initialized

st: Version 20041025, fixed bufsize 32768, s/g segs 256

NET: Registered protocol family 17

usbcore: registered new driver hiddev

input: USB HID v1.10 Mouse [Microsoft Microsoft(R) Compact Optical Mouse] on usb-0000:00:03.1-2

usbcore: registered new driver usbhid

drivers/usb/input/hid-core.c: v2.01:USB HID core driver

eth0: Media Link On 100mbps full-duplex

eth0: no IPv6 routers present

Non-volatile memory driver v1.2

bootsplash: status on console 0 changed to on

ACPI: AC Adapter [AC0] (on-line)

ACPI: Battery Slot [BAT0] (battery present)

ACPI: Power Button (FF) [PWRF]

ACPI: Lid Switch [LID]

ACPI: Sleep Button (CM) [SLPB]

ACPI-0484: *** Warning: Error getting cpuindex for acpiid 0x2

ACPI: Thermal Zone [THRM] (75 C)

powernow: This module only works with AMD K7 CPUs

drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic

usbcore: registered new driver usbserial_generic

usbcore: registered new driver usbserial

drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0

bootsplash: status on console 0 changed to on

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=7 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=8 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=9 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86

subfs 0.9

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

ISO 9660 Extensions: Microsoft Joliet Level 3

ISOFS: changing to secondary root

hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }

hdc: packet command error: error=0x50 { LastFailedSense=0x05 }

ide: failed opcode was: unknown

NET: Registered protocol family 4

ax25: unsupported module, tainting kernel.

NET: Registered protocol family 3

NET: Registered protocol family 5

eth0: Media Link Off

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=1 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=2 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=3 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=4 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=8 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86

SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.1.34 DST=224.0.0.251 LEN=106 TOS=0x00 PREC=0x00 TTL=255 ID=9 DF PROTO=UDP SPT=5353 DPT=5353 LEN=86



Gruss, dueppe



Man sollte eigentlich im Leben niemals die gleiche Dummheit 2x machen, denn die Auswahl ist so groß.




geschrieben von

Login

E-Mail:
  

Passwort:
  

Beitrag anfügen

Symbol:
 
 
 
 
 
 
 
 
 
 
 
 
 

Überschrift: